PRTG Manual: SNTP Sensor
The SNTP sensor monitors a Simple Network Time Protocol (SNTP) server.
The sensor tries to get a valid time stamp from the server up to three times per scan until it reports an error.
For a detailed list and descriptions of the channels that this sensor can show, see section Channel List.
- Dutch: SNTP
- French: SNTP
- German: SNTP
- Japanese: SNTP
- Portuguese: SNTP
- Russian: SNTP
- Simplified Chinese: SNTP
- Spanish: SNTP
- This sensor supports the IPv6 protocol.
- This sensor has a low performance impact.
The Add Sensor dialog appears when you manually add a new sensor to a device. It only shows the settings that are required to create the sensor. You can change nearly all settings on the sensor's Settings tab after creation.
Click the Settings tab of a sensor to change its settings.
Setting |
Description |
---|---|
Sensor Name |
Enter a name to identify the sensor. |
Parent Tags |
Shows tags that the sensor inherits from its parent device, parent group, and parent probe. This setting is for your information only. You cannot change it. |
Tags |
Enter one or more tags. Confirm each tag with the Spacebar key, a comma, or the Enter key. You can use tags to group objects and use tag-filtered views later on. Tags are not case-sensitive. Tags are automatically inherited. It is not possible to enter tags with a leading plus (+) or minus (-) sign, nor tags with parentheses (()) or angle brackets (<>). For performance reasons, it can take some minutes until you can filter for new tags that you added. The sensor has the following default tags that are automatically predefined in the sensor's settings when you add the sensor:
|
Priority |
Select a priority for the sensor. This setting determines the position of the sensor in lists. The highest priority is at the top of a list. Choose from the lowest priority () to the highest priority (). |
Usually, a sensor connects to the IP Address/DNS Name of the parent device. See the device settings for details. For some sensors, you can explicitly define the monitoring target in the sensor settings.
Setting |
Description |
---|---|
Timeout (Sec.) |
Enter a timeout in seconds for the request. Enter an integer. The maximum timeout value is 900 seconds (15 minutes). If the reply takes longer than this value, the sensor cancels the request and shows a corresponding error message. |
Setting |
Description |
---|---|
Primary Channel |
Select a channel from the list to define it as the primary channel. In the device tree, the last value of the primary channel is always displayed below the sensor's name. The available options depend on what channels are available for this sensor. You can set a different primary channel later by clicking below a channel gauge on the sensor's Overview tab. |
Graph Type |
Define how different channels are shown for this sensor:
|
Stack Unit |
This setting is only visible if you enable Stack channels on top of each other as Graph Type. Select a unit from the list. All channels with this unit are stacked on top of each other. By default, you cannot exclude single channels from stacking if they use the selected unit. However, there is an advanced procedure to do so. |
By default, all of these settings are inherited from objects that are higher in the hierarchy. We recommend that you change them centrally in the root group settings if necessary. To change a setting for this object only, click under the corresponding setting name to disable the inheritance and to display its options.
For more information, see section Inheritance of Settings.
For more information, see section Root Group Settings, section Scanning Interval.
Schedules, Dependencies, and Maintenance Window
You cannot interrupt the inheritance for schedules, dependencies, and maintenance windows. The corresponding settings from the parent objects are always active. However, you can define additional schedules, dependencies, and maintenance windows. They are active at the same time as the parent objects' settings.
For more information, see section Root Group Settings, section Schedules, Dependencies, and Maintenance Window.
For more information, see section Root Group Settings, section Access Rights.
Which channels the sensor actually shows might depend on the target device, the available components, and the sensor setup.
Channel |
Description |
---|---|
Difference |
The time difference in comparison to the local system time |
Downtime |
In the channel table on the Overview tab, this channel never shows any values. PRTG uses this channel in graphs and reports to show the amount of time in which the sensor was in the Down status in percent. |
Response Time |
The response time in msec This channel is the primary channel by default. |
Knowledge Base
What security features does PRTG include?