PRTG Manual: NetFlow v5 (Custom) Sensor
The NetFlow v5 (Custom) sensor receives traffic data from a NetFlow v5-compatible device and shows the traffic by type. With this sensor, you can define your own channel definitions to divide traffic into different channels.
Make sure that the sensor matches the NetFlow version that your device exports.
For a detailed list and descriptions of the channels that this sensor can show, see section Channel List.
- Dutch: NetFlow v5 (aangepast)
- French: NetFlow v5 personnalisé
- German: NetFlow v5 (Benutzerdefiniert)
- Japanese: NetFlow v5(カスタム)
- Portuguese: NetFlow v5 (customizado)
- Russian: NetFlow v5 (настраиваемый)
- Simplified Chinese: NetFlow v5 (自定义)
- Spanish: NetFlow v5 (personalizado)
Consider the following remarks and requirements for this sensor:
Remark |
Description |
---|---|
Performance impact |
This sensor has a very high performance impact. We recommend that you use no more than 50 of this sensor on each probe. |
NetFlow |
This sensor requires that the NetFlow export of the respective version is enabled on the target system. The target system must send the flow data stream to the IP address of the probe system. |
Channels |
This sensor does not officially support more than 50 channels. |
Cluster probe |
This sensor does not support cluster probes. You can only set it up on local probes or remote probes. |
IPv6 |
This sensor supports IPv6. |
Knowledge Base |
Knowledge Base: What is the Active Flow Timeout in flow sensors? |
Hosted probe |
You cannot add this sensor to the hosted probe of a PRTG Hosted Monitor instance. If you want to use this sensor, add it to a remote probe device. |
The sensor has the following default tags that are automatically predefined in the sensor's settings when you add the sensor:
- bandwidthsensor
- netflowsensor
For more information about basic sensor settings, see section Sensor Settings.
Setting |
Description |
---|---|
Receive Packets on UDP Port |
Enter the User Datagram Protocol (UDP) port number on which PRTG receives the flow packets. It must match the UDP port number in the NetFlow export options of the hardware router device. Enter an integer. When you configure the export, make sure that you select the appropriate NetFlow version for this sensor. |
Sender IP Address |
Enter the IP address of the sending device that you want to receive the NetFlow from. Enter an IP address to only receive data from a specific device or leave the field empty to receive data from any device on the specified port. |
Receive Packets on IP Address |
Select the IP addresses on which PRTG listens to NetFlow packets. The list of IP addresses is specific to your setup. To select an IP address, enable a check box in front of the respective line. The IP address that you select must match the IP address in the NetFlow export options of the hardware router device. When you configure the export, make sure that you select the appropriate NetFlow version for this sensor. You can also select all items or cancel the selection by using the check box in the table header. |
Active Flow Timeout (Minutes) |
Enter a time span in minutes after which the sensor must receive new flow data. If the timeout elapses and the sensor receives no new data during this time, it shows the Unknown status. Enter an integer. The maximum timeout is 60 minutes. We recommend that you set the timeout one minute longer than the timeout in the hardware router device. If you set this value too low, flow information might be lost. For more information, see the Knowledge Base: What is the Active Flow Timeout in flow sensors? If the target device sends incorrect time information that results in wrong monitoring data, try to use 0 as the active flow timeout. This ignores the start and stop information of a flow as provided by the device and accounts all data to the current point in time. It might result in spikes but the sensor captures all data. |
Sampling Mode |
Define if you want to use the sampling mode:
This setting must match the setting in the xFlow exporter. |
Sampling Rate |
This setting is only visible if you select Enable above. Enter a number that matches the sampling rate in your device that exports the flows. If the number is different, monitoring results will be incorrect. Enter an integer. |
Channel Definition |
Enter a channel definition to divide the traffic into different channels. Enter each definition in one line. The sensor accounts all traffic that you do not define a channel for to the default channel Other. For more information, see section Channel Definitions for Flow, IPFIX, and Packet Sniffer Sensors. Extensive use of many filters can cause load problems on the probe system. We recommend that you define specific, well-chosen filters for the data that you really want to analyze. We recommend that you do not use more than 20 channels in graphs and tables, and not more than 100 channels in total. For performance reasons, we recommend that you add several sensors with fewer channels each. |
Stream Data Handling |
Define what PRTG does with the stream and packet data:
Use with caution. It can create huge data files. We recommend that you only use this setting for a short time. |
For more information, see section Filter Rules.
Setting |
Description |
---|---|
Include Filter |
Define if you want to filter any traffic. If you leave this field empty, the sensor includes all traffic. To include specific traffic only, define filters using a special syntax. |
Exclude Filter |
First, the sensor considers the filters in Include Filter. From this subset, you can explicitly exclude traffic, using the same syntax. |
Setting |
Description |
---|---|
Primary Channel |
Select a channel from the list to define it as the primary channel. In the device tree, PRTG displays the last value of the primary channel below the sensor's name. The available options depend on what channels are available for this sensor. You can set a different primary channel later by clicking below a channel gauge on the sensor's Overview tab. |
Graph Type |
Define how this sensor shows different channels:
|
Stack Unit |
This setting is only visible if you select Stack channels on top of each other above. Select a unit from the list. PRTG stacks all channels with this unit on top of each other. By default, you cannot exclude single channels from stacking if they use the selected unit. However, there is an advanced procedure to do so. |
Setting |
Description |
---|---|
Primary Toplist |
Define which Toplist is the primary Toplist of the sensor:
PRTG shows the primary Toplist in maps when you add a Toplist object. |
By default, all of these settings are inherited from objects that are higher in the hierarchy. We recommend that you change them centrally in the root group settings if necessary. To change a setting for this object only, click under the corresponding setting name to disable the inheritance and to display its options.
For more information, see section Inheritance of Settings.
For all Flow (NetFlow, jFlow, sFlow, IPFIX) and Packet Sniffer sensors, Toplists are available on the sensor's Overview tab. Using Toplists, you can review traffic data for small time periods in great detail.
For more information, see section Toplists.
For more information, see section Filter Rules for Flow, IPFIX, and Packet Sniffer Sensors.
Which channels the sensor actually shows might depend on the target device, the available components, and the sensor setup.
Channel |
Description |
---|---|
[Custom] |
The traffic by type according to the channel definition |
Downtime |
In the channel table on the Overview tab, this channel never shows any values. PRTG uses this channel in graphs and reports to show the amount of time in which the sensor was in the Down status |
Other |
All traffic for which no channel is defined |
Total |
The total traffic This channel is the primary channel by default. |
KNOWLEDGE BASE
What is the Active Flow Timeout in flow sensors?
What security features does PRTG include?
Where is the volume line in graphs?
PAESSLER TOOLS
NetFlow Tester