There are a lot of Western Digital Hard Disk
Errors out there. Way too much, right?
You as a Sysadmin know that for sure – Fatal Errors, Cyclic Redundancy Check Errors, I/O Device Errors,
Format Errors, Disk Read Errors, and Connection Problems.
Here you’ll find a list of the most common Western Digital hard disk errors and proven quick fix solutions:
- WD Hard Disk Error Code “BIOHD-8” or “SMART drive error code BIOHD-8”
- WD Hard Disk Error “Fatal Error”
- WD Hard Disk Error “Data Error Cyclic Redundancy Check” “ or “CRC Error“
- WD Hard Disk Error “I/O Device Error”
- WD Hard Disk Error “Error Code 43”
- WD Hard Disk Error “Format Error”
- WD Hard Disk Error “Disk Read Error”
- WD Hard Disk Error “Slow Transfer Rate”
- WD Hard Disk Error “Connection Problem” or “Hard Disk Not Recognized”
And you’ll find the solution to get rid of ALL Western Digital hard disk errors – forever:
Test PRTG as your new monitoring tool and get stared within minutes!
Quick fix
Are you getting the error code BIOHD-8 while using your Western Digital hard drive? BIOHD-8 is a common error issued when the HP SMART diagnostic tool thinks that your hard drive is failing. The error can be caused by damaged connections, overheating, or firmware issues.
To get rid of the error code, try the following solutions:
- Ensure that your WD hard disk and your computer or laptop are properly connected.
- Check if there are any issues with your hard disk by using the SMART Drive Monitor.
- If a replacement of your hard disk is necessary, do not forget to use a data recovery software to recover all files from your WD hard disk.
Best solution: https://www.stellarinfo.com/blog/smart-error-biohd-8/
Proper fix
Switch to PRTG: PRTG checks your hard disks round the clock, displays all memory capacities on just one dashboard, and informs you before reaching disk space limit.
Find out how PRTG can help you get rid of Western Digital Hard Disk Errors
Quick fix
Fatal errors are a common problem among Western Digital hard disk users. In some cases, the error indicates that your hard disk is seriously damaged and needs to be replaced. However, the fatal error message can also be triggered by other reasons, such as a loose connection, corrupted files, or outdated firmware.
These basic troubleshooting steps can resolve the issue in most cases.
- Sometimes, a simple restart will fix the problem. Shut down both your computer and your WD hard disk, then restart and check if the error persists.
- If the error is caused by an incompatible USB cable, or a malfunctioning USB port, connecting your hard disk using a different cable and USB port may help you get rid of the fatal error.
- Check all connections, including the power cable, as loose cables are a common cause of the fatal error.
- To determine whether the fatal error is caused by your Western Digital hard disk or by your computer, try using your hard disk with a different PC or laptop. If the hard disk works, there might be a problem with your computer.
- Western Digital provides a diagnostic tool the run disk tests on your WD hard disk. Use WD drive utilities to check for any hard drive issues.
- If your hard disk is damaged beyond repair, use a data recovery software to recover all data before replacing the hard disk with a new one.
Best solution: https://windowsreport.com/fatal-error-external-hard-drive/
Proper fix
Switch to PRTG: PRTG checks your hard disks round-the-clock, displays all memory capacities on just one dashboard, and informs you before reaching disk space limit.
Find out how PRTG can help you get rid of Western Digital Hard Disk Errors
Quick fix
A cyclic redundancy check error, or CRC error, indicates a bad spot in your hard disk. The CRC error can be caused by misconfigures files, registry corruption, or a cluttered hard disk. It is a serious error that may lead to data loss or system failure. Therefore, it is advisable to solve the problem right away when the error occurs.
Follow these steps to fix the cyclic redundancy check error as quickly as possible:
- Run the built-in Windows tool CHKDSK to fix logical file system errors and metadata of the file system.
- If the error persists, use a different disk scan program, for example HDDScan, to determine and to repair corrupt files.
- If neither solution helps, recover all data from your damaged hard drive using a data recovery tool, then replace the WD hard disk.
Best solution: https://www.wikihow.com/Fix-a-Cyclic-Redundancy-Check-Error
Proper fix
Switch to PRTG: PRTG checks your hard disks round-the-clock, displays all memory capacities on just one dashboard, and informs you before reaching disk space limit.
Find out how PRTG can help you get rid of Western Digital Hard Disk Errors
Quick fix
Are you struggling with an I/O device error while using your Western Digital hard disk? Then you are dealing with a common Input/Output error that occurs when an external hard disk encounters a reading and writing problem.
To solve the WD hard disk I/O device error, follow these steps:
- Restart both your PC and your hard disk. A simple restart can often fix Input/Output errors. If the error persists, continue with the next step.
- Make sure that your external hard disk and your laptop or PC are properly connected. Loose connections or damaged cables may cause an I/O error. If this is the case, you can easily fix the problem by reconnecting or replacing all cables.
- Check if any driver of other software is causing the Input/Output error on your Western Digital hard disk by performing a clean boot of your computer.
- Access the IDE channel properties to ensure that the drive’s transfer mode is correct.
- If you cannot get rid of the I/O error, you may need to replace your WD hard disk. Do not forget to recover all data from your hard drive before you take further actions.
Best solution:
or: https://www.lifewire.com/how-to-scan-a-hard-drive-using-error-checking-2624497
Proper fix
Switch to PRTG: PRTG checks your hard disks round the clock, displays all memory capacities on just one dashboard, and informs you before reaching disk space limit.
Find out how PRTG can help you get rid of Western Digital Hard Disk Errors
Quick fix
If you see the error message “error code 43” or “Windows hast stopped this device because it has reported problems (code 43)”, you are facing a common hardware issue. The error occurs when Windows experiences a problem with an USB device such as your Western Digital hard disk. Error code 43 can be caused by a failure of the hard disk or the driver.
As with most hard disk errors, the solution depends on the actual cause of the problem. To get rid of error code 43, try the following troubleshooting steps:
- Restart your computer and your WD hard disk.
- Check for updates of your hard disk driver and install the latest version.
- Make sure that the hard disk is enabled and properly connected to your computer.
- Update the BIOS.
- If you made changes in the Windows Device Manager, restore the system to an earlier version to fix the problem.
Best solution: https://www.easeus.com/resource/code-43-usb.html#5
Proper fix
Switch to PRTG: PRTG checks your hard disks round the clock, displays all memory capacities on just one dashboard, and informs you before reaching disk space limit.
Find out how PRTG can help you get rid of Western Digital Hard Disk Errors
Quick fix
If you receive a format error message with your WD hard disk, this problem can occur due to file corruption, malware, write protection, and others causes.
To fix the problem, check whether your WD hard drive is write-protected. If this is the case, your hard disk cannot be formatted correctly and the error occurs. To solve the problem, disable the write protection.
If the error persists, go to Diskpart and clean your Western Digital hard disk, then create a new partition. To avoid the loss of data, use a data recovery tool.
Best solution: https://www.diskpart.com/articles/wd-external-hard-drive-will-not-format-0310.html
Proper fix
Switch to PRTG: PRTG checks your hard disks round the clock, displays all memory capacities on just one dashboard, and informs you before reaching disk space limit.
Find out how PRTG can help you get rid of Western Digital Hard Disk Errors
Quick fix
Read errors are among the most common WD hard disk errors. The problem is often indicated by the error message “A disk read error occurred”. This message indicates that the operating system is not able to access and read your Western Digital hard drive.
The following solutions can fix the disk read error.
- Access the BIOS setting and make sure that the boot order is correct. If necessary, change the order in the settings.
- Reset the BIOS to default.
- The disk read error can also be caused by a damaged Master Boot Record. Use a repair tool to fix the issue.
- Make sure your WD hard disk is well connected to your computer. If necessary, reconnect or replace any loose or damaged cables.
- Test the RAM of your computer to determine whether the disk read error is related to a faulty RAM stick or slot.
- Remember to recover your data by using a data recovery tool before repairing or replacing your Western Digital hard disk.
Best solution: https://www.partitionwizard.com/partitionmagic/disk-read-error.html
Proper fix
Switch to PRTG: PRTG checks your hard disks round the clock, displays all memory capacities on just one dashboard, and informs you before reaching disk space limit.
Find out how PRTG can help you get rid of Western Digital Hard Disk Errors
Quick fix
Are you tired of the slow transfer rate of your WD hard disk? There are several possible causes of a slow transfer rate. The most common issues are low storage space, a cluttered hard drive, and corrupted system files.
If you are experiencing a slow transfer rate with your Western Digital hard disk due to a lack of storage place, compress any files that are not frequently used. Using a backup software, you can compress and backup your data to avoid taking up too much space on your hard disk.
A slow transfer rate caused by a cluttered hard disk can be repaired by getting rid of useless big files and junk files on your WD hard disk. You can remove the files manually or use a file cleaner software.
Another solution to speed up your Western Digital hard disk is to repair any corrupted system files on the hard drive. For easy troubleshooting, use a software like CHKDSK.
Best solution: https://www.easeus.com/todo-backup-resource/speed-up-wd-external-hard-drive-slow-transfer-rate.html
Proper fix
Switch to PRTG: PRTG checks your hard disks round the clock, displays all memory capacities on just one dashboard, and informs you before reaching disk space limit.
Find out how PRTG can help you get rid of Western Digital Hard Disk Errors.
Quick fix
If your Western Digital hard drive is not recognized and does not show up on your computer, you are facing a common problem. The error is often caused by incompatible file systems, problems with the USB connection, or outdated drivers.
When facing this issue, a simple restart of your computer and your WD hard disk may already do the trick. If not, you may have to update the WD hard drive device driver, enable the USB device in BIOS, or format your Western Digital hard disk to a compatible file system. Another possible solution is to switch the connection port, as a damaged USB port can also cause a connection error.
Best solution: https://www.diskpart.com/windows-10/wd-hard-drive-not-recognized-windows-10-0310.html
Proper fix
Switch to PRTG: PRTG checks your hard disks round the clock, displays all memory capacities on just one dashboard, and informs you before reaching disk space limit.
Find out how PRTG can help you get rid of Western Digital Hard Disk Errors
Choose your solution: Bugfix or replacement
Trusted by 500,000 users and recognized
by industry analysts as a leader
“Fantastic network and infrastructure monitoring solution that is easy to deploy and easier still to use. Simply the best available.”
“Software is absolutely perfect, Support is superior. Meets all needs and requirements, this is a must have solution if you are needing any form of monitoring.”
“The tool excels at its primary focus of being a unified infrastructure management and network monitoring service.”