There are a lot of HP errors out there.
Way too many, right?

Quick fix

This HP printer error is a common error when sending a document for printing. The error message indicates that the printer is either turned off, not properly connected to your computer or missing an internet connection. Another possible reason for the general error state is that your HP printer is running low on paper or ink.

To fix the error, try the following steps:

• Make sure the printer is turned on. You can also restart both the printer and your computer.
• Check if the printer is connected to your computer or WI-FI network.
• Make sure the paper try of your printer is loaded and that the printer has enough ink.
• If the error still occurs, contact the HP printer support.

Best Solution: https://www.hpprintersupportpro.us/blog/hp-printer-in-error-state/

Quick fix

The HP printer error 59.F0 indicates that there is a problem with the internal motor of your HP printer. The most common cause of the problem is the failure in transfer alienation, meaning that the ITB is stuck and unable to rotate. The error 59.f0 can also be caused by a problem of the SR9 sensor.

To solve the issue, reset the printer settings and remove the surge protector. If this does not solve the problem, reset the ITB and check its internal connections. If the ITB is damaged, you may have to replace it in order to get rid of the HP error.

Best Solution: https://www.printerfixes.com/how-to-fix-hp-printer-error-59-f0/

Quick fix

The HP hard drive error 3F0 may occur when the system boot process is not supported by the hard disk. The cause can be a hard drive connection issue, an incorrect boot sequence in the Basic Input-Output System (BIOS), a malware attack, or a damaged hard drive.

If you are facing HP error 3F0 and the boot device is not, solve the problem by following these simple steps:

1. Hard Reset: By performing a hard reset, you can erase all information in the computer memory. This forces the system to reestablish the connection between the hard drive and the BIOS.
2. BIOS Settings: Another possible solution is to restore the BIOS default settings in the BIOS Setup section. After the reset, restart your computer and check if the error still occurs.
3. Hard Drive Test: Use HP PC Hardware Diagnostics to run either a quick test or an extensive test, and review the error log afterwards.
4. Hard Drive Reseat: If the first steps did not solve HP error 3F0, check if your hard drive is damaged or needs to be reseated.

Best Solution: https://support.hp.com/sk-en/document/c01443463

Quick fix

The HP printer error 79 usually occurs when a print job is either corrupted or when the connection between the HP printer and the print spooler is not working.

To solve HP error 79, make sure that your firmware is up to date and that the connection between printer and software is working properly. If this does not help, remove all print jobs from the computers that have access to the printer. Then remove your HP printer from the list of devices in your network. Reestablish the connection and try again.

Best Solution:   https://www.errorsdoc.com/hp/how-to-fix-79-service-error-code-on-hp-laserjet-pro-400-printer/989

Quick fix

The listener received a request to set up a connection to a database or other service. The connect descriptor that has been received by the listener specified a service name for a service (usually a database service). Either it has not been dynamically registered with the listener yet or has not been configured statically for the listener. This can be a temporary condition, for example, after the listener has been started, but before the database instance has registered with the listener.

Hint:

• Wait a moment and try to reconnect.
• Find out which services are currently known by the listener by executing: lsnrctl services <listener name>
• Dopple-check that the SERVICE_NAME parameter in the connect descriptor of the net service name used specifies a service known to the listener.
• If an easy connect naming connect identifier was used, prove that the service name specified is a service known to the listener.
• Check in the listener.log file for an event.

Best solution:

https://docs.oracle.com/cd/B28359_01/server.111/b28278/net12500.htm#ORA-12514

Quick fix

If you receive error 601 by your HP laptop, you are facing battery problems. The error occurs when the primary battery of your HP laptop has a low capacity.

You can check the battery health in the system diagnostics of your laptop. If the test confirms that the capacity of the primary battery is low, try to re-attach the battery. This is a quick-fix solution that may help you get rid of the error code 601. If it does not solve the problem, the battery may be damaged beyond repair. In this case, simply replace it by a new battery.

Best Solution: https://www.hptechnicalsupportphonenumber.com/blog/hp-error-code-601/

Quick fix

HP error 90b or error 90f occurs while starting the HP laptop. Both error codes indicate that there is a problem with the HP laptop system fan. It is not recommended to continue using the laptop, because the cooling fan is not working properly, which could lead to an accidental shutdown and the loss of your data. If HP error 90b orrucs, the laptop usually shuts down within 15 seconds.

To solve HP system fan error 90b, follow these steps:

1. Clean the exterior vents of your laptop. Remove any dust that may harm the cooling fan. Restart your computer to check if the error still occurs.
2. Perform a hard reset of the computer. This may enable you to use the computer long enough to store your data to an external hard drive before the laptop shuts down again.
3. Update the BIOS of your laptop. In some cases, this solves the issue of error 90b.
4. Get in touch with HP service or an official partner and have all internal components cleaned properly. If necessary, replace the damaged system fan.

Best Solution: https://support.hp.com/za-en/document/c04935023

Quick fix

Error code 0xc19a0003 is one of the most common HP printer error codes. The error indicates an ink leakage at the bottom of the printer. The leakage could be caused by a damaged ink cartridge or by a problem with the printhead. While error 0xc19a0003 occurs, the printer is usually not able to print.

To fix the problem, remove the damaged ink cartridge immediately and replace it by new one. Carefully clean the printhead. Afterwards, reset your HP printer. It should now work properly.

Best Solution: https://www.hpsupportphonenumbers.com/hp-printer-error-0xc19a0003/

Quick fix

This is the generic internal error number for Oracle program exceptions. This points to a process encountering an abnormal condition.

Hint:

Report it as a bug – the internal error number is the first argument.

Best solution:

https://docs.oracle.com/cd/B28359_01/server.111/b28278/e0.htm#ORA-00600

Quick fix

During startup, your HP desktop PC may make on or two short beeps, which is normal. However, if the computer beeps several times and Windows does not start correctly, the beeps may indicate a hardware problem, such as memory or heat-related failures, a stuck keyboard key, incorrect seating of hard drive cables, failure of motherboard component, or problems with other functions.

To solve the problem, listen carefully how many beeps occur. The number of beeps may help you identify the problem. Check the beep codes in the HP support chart, then fix the cause of the beeps.

Best Solution: https://support.hp.com/us-en/document/c02222922

Quick fix

If you receive an accelerometer error while starting your HP device, this can easily be solved. The error message usually occurs after a Windows software update, which keep some drivers from running properly. The HP accelerometer error is usually caused by either a file corruption or by an outdated driver.

There are three possible solutions to fix the HP accelerometer error:

1. Check for Windows updates. After updating, restart your device.
2. Updating all existing drivers in the Device Manager.
3. Remove any corrupted drivers, then reinstall them.

Best Solution: https://windowsreport.com/fix-hp-accelerometer-error/

Quick fix

E8 is a common error code for HP Laserjet printers. The error message indicates a problem with the scanner carriage of your printer. This problem can either be software based, or caused by a problem with the scanner motor.

First, make sure that your HP printer software is up to date. If error E8 still occurs, you are most definitely facing a hardware problem. Removing the ink cartridge and cleaning all the printer roller should quickly solve the problem. Maintaining and cleaning of the hardware is the key to prevent HP printer error E8.

Best Solution: https://www.hpprintersupporthelpline.com/how-to-resolve-hp-laserjet-pro-m1132-error-e8

Quick fix

Another common HP printer error code is error 61011bed, or 0x61011bed. Both error codes indicate a problem with the printer head of your HP printer. It may also occur while you try to align the ink cartridges.

How to solve the problem of HP error 61011bed:

1. Remove the ink cartridges and clean the printer head thoroughly. If this does not help, continue with the next step.
2. Reinstall the ink cartridges of your HP printer, then restart the print job.
3. Update the printer drivers to make sure that the communication between the printer and your computer works properly.
4. Clean the registry by installing and running the RegAce System Suite registry cleaner.
5. If none of the above solutions work, contact the HP technical support.

Best Solution: https://medium.com/@cindyguerra622/how-to-fix-hp-printer-error-61011bed-9fa43884b8fc